AI Summary

Product: Selleys Wet Area Ezi Press Brand: Selleys (a division of DuluxGroup Australia Pty Ltd) Category: Pressurised aerosol silicone sealant Primary Use: Sealing joints and gaps in wet areas such as bathrooms, kitchens, and laundries without a caulking gun.

Quick Facts

Best For: DIYers and trade users tackling small to medium wet area sealing jobs in residential settings
Key Benefit: Aerosol format delivers consistent sealant pressure with no caulking gun required, cutting hand fatigue and skipping the learning curve of manual application
Form Factor: Pressurised aerosol canister (100g), available in Clear and White
Application Method: Direct nozzle into joint, press actuator, move steadily along the gap; tool the bead before a skin forms

Common Questions This Guide Answers

Does Selleys Wet Area Ezi Press require a caulking gun? → No — the pressurised aerosol canister dispenses sealant automatically without any separate applicator tool
Is this product classified as hazardous or dangerous? → Non-hazardous under GHS Version 7 (Safe Work Australia), but classified as Dangerous Goods Class 2.2 (Non-Flammable, Non-Toxic Gases) because it's a pressurised aerosol canister; UN transport number UN 1950
What is the maximum safe storage temperature? → Below 50°C, in a cool, dry, well-ventilated place away from direct sunlight, ignition sources, and oxidising agents

Product Overview

Selleys Wet Area Ezi Press is a pressurised aerosol silicone sealant built for wet area sealing in residential and trade settings. Manufactured by Selleys, a division of DuluxGroup Australia Pty Ltd, it pushes silicone sealant through an aerosol canister — no caulking gun, no fuss. Available in a 100g pressurised canister in Clear and White, it covers the most common aesthetic requirements in kitchens, bathrooms, and laundries.

What separates this from traditional tube or cartridge silicone is the delivery mechanism. The aerosol format uses a pressurised canister to dispense sealant at a consistent rate — no separate applicator tool, no manual pressure. It's the practical choice for smaller sealing jobs, touch-up work, and any situation where getting it right the first time matters.

Key Features and What They Mean in Practice

Aerosol delivery format

The aerosol canister is the standout feature of Selleys Wet Area Ezi Press, and it changes how you seal. With conventional silicone, you load a cartridge into a caulking gun and apply manual force to push sealant through a nozzle. With this aerosol format, the propellant gas inside the canister does that work — automatically and consistently. The result is steady, even pressure throughout the application, less hand fatigue, and no need to own or maintain a separate caulking gun.

For DIYers tackling repairs or small sealing jobs, this is a genuine advantage. The learning curve that comes with controlling a caulking gun — avoiding surging, keeping a steady bead — is gone. You get good results from the first use.

Silicone formulation for wet areas

Selleys Wet Area Ezi Press uses a silicone sealant formulation, which is the right chemistry for wet area applications. Silicone stays flexible after curing, resists water penetration, and handles the thermal expansion and contraction that happens around baths, showers, sinks, and splashbacks. Unlike acrylic sealants, silicone doesn't absorb water and holds strong adhesion on non-porous surfaces including ceramic tiles, glass, and vitreous enamel.

The wet area designation means this formulation is built specifically for conditions involving regular water exposure, humidity, and cleaning products — the everyday environment of a bathroom or kitchen.

Available colours

Selleys Wet Area Ezi Press comes in Clear and White. White suits most bathroom and kitchen installations where grout, fixtures, and trims are white. Clear works where a less visible seal is preferred, or where the substrate colour varies and a neutral finish gives the best result. Both options come in the same aerosol format.

Practical Applications and Use Cases

Selleys Wet Area Ezi Press is designed for sealing joints and gaps in wet areas. Typical applications include:

Bath and shower surrounds: Sealing the junction between a bath rim and tiled wall, or around a shower base where it meets the wall, stops water from tracking behind surfaces and causing structural damage or mould growth.
Sink and basin surrounds: The joint between a sink and benchtop, or between a vanity basin and the wall, is one of the most common points of water ingress in kitchens and bathrooms.
Splashbacks: Sealing the lower edge of a splashback where it meets a benchtop or cooktop surround keeps moisture out of the substrate and protects surfaces long-term.
Window frames in wet areas: Bathroom windows often need sealing at the junction with tiled walls, a job this product handles without difficulty.
General gap sealing: Any gap in a wet area where water could penetrate and where flexibility is needed to accommodate movement.

The 100g canister size suits these tasks individually or in combination. It's not designed for large-scale commercial sealing projects, where a 300ml or 600ml cartridge would typically be more economical — but for the jobs it's built for, it delivers.

Safety Classification and What It Means

Understanding the safety classification of Selleys Wet Area Ezi Press matters for safe handling, storage, and transport. The product carries a dual classification that is sometimes misunderstood.

Non-hazardous under GHS

The product is classified as non-hazardous according to the Globally Harmonised System of Classification and Labelling of Chemicals (GHS), Version 7, as adopted by Safe Work Australia. This classification covers health and environmental hazard categories — the product doesn't meet the criteria for being classified as toxic, corrosive, carcinogenic, or environmentally hazardous under this framework.

For users, this means standard precautions apply: work in a ventilated area, avoid prolonged skin contact, and keep out of reach of children. It doesn't require the elevated handling procedures associated with hazardous chemical products.

Dangerous Goods Class 2.2

Separately, the product is classified as Dangerous Goods Class 2.2 (Non-Flammable, Non-Toxic Gases) under the Australian Dangerous Goods Code. This classification applies because the product is an aerosol — the pressurised canister itself, not the sealant chemistry, is the basis for this classification.

Aerosol Category 3 under this framework covers non-flammable aerosols. The distinction matters: this product is not flammable in the way that aerosol paints or spray lubricants often are. However, because it's a pressurised container, it remains subject to Dangerous Goods regulations for storage and transport.

The UN number for transport is UN 1950, with the proper shipping name AEROSOLS. For air transport, the designation is NON-FLAMMABLE. This is relevant for anyone transporting or shipping the product commercially, or for workplaces that need to comply with dangerous goods storage requirements.

For home users, the practical takeaway is simple: keep the product away from heat sources, open flames, and direct sunlight. Don't puncture or incinerate the canister — standard practice for any aerosol product.

Storage Requirements

Storing Selleys Wet Area Ezi Press correctly preserves both product performance and safety:

Temperature: Store below 50°C. Aerosol canisters are pressure vessels — elevated temperatures increase internal pressure and can cause the canister to rupture or leak. In Australian conditions, this means keeping the product out of vehicles, garden sheds, or anywhere summer temperatures can push past this threshold.
Environment: Store in a cool, dry, well-ventilated place. Good ventilation matters in the event of any minor propellant gas leakage.
Away from sunlight: Direct sunlight raises temperature and can degrade the canister over time.
Away from ignition sources: Even though this product is non-flammable, keeping any pressurised aerosol away from ignition sources is sound practice.
Away from oxidising agents: Oxidising agents can react with aerosol propellants or sealant components — store them separately.

These requirements align with Australian Standards for aerosol storage and are consistent with the Dangerous Goods Class 2.2 classification.

Application Guidance

Surface preparation

Good sealing starts with good preparation. For Selleys Wet Area Ezi Press to perform well, the substrate needs to be:

Clean: Remove existing sealant, soap scum, mould, and cleaning product residue. Old silicone comes off with a silicone remover or a careful blade tool. Any remaining residue will undermine adhesion — take the time to get it right.
Dry: Silicone sealant needs a dry surface for proper adhesion. Even in a wet area application, the surface must be completely dry at the time of sealing.
Free of grease and dust: Wipe surfaces with an appropriate cleaner and allow them to dry fully before starting.

Application

With the aerosol format, application is straightforward — direct the nozzle into the joint, press the actuator, and move steadily along the gap. A few things to keep in mind:

Maintain a consistent distance from the surface and a consistent speed to produce an even, clean bead.
Apply in a single, continuous pass where possible to avoid joins in the sealant line.
The aerosol delivers consistent pressure, but movement speed is in your hands. Move too slowly and you'll get excess sealant; move too quickly and the bead will be incomplete. Find your rhythm and keep it steady.

Tooling and finishing

Once the sealant is applied, tool the bead promptly before a skin forms on the surface. A damp finger, a dedicated sealant tool, or a smoothing tool dipped in soapy water presses the sealant into the joint and creates a clean, concave finish. For the sharpest result, apply masking tape to either side of the joint before sealing and pull it away immediately after tooling.

Curing

Silicone sealants cure through exposure to atmospheric moisture. In a wet area environment, ambient humidity typically supports curing well. Keep the area away from water until curing is complete. Curing time varies depending on temperature, humidity, and bead thickness — check the product packaging for specific cure times. Avoid applying in very cold or very dry conditions, which slow the curing process.

Expert Tips and Best Practices

Joint size matters: Silicone performs best when applied to joints of the right width — not too narrow (which limits adhesion area) and not excessively wide (which can cause the sealant to sag before curing). For most bathroom joints, a bead of 6–10mm is the target.
Mould prevention: Mould growth on sealant is a common long-term issue in wet areas. Keep the area well-ventilated after sealing and during regular use. When sealant eventually shows mould that can't be cleaned away, the right move is full replacement — not applying new sealant over old.
Canister orientation: Follow manufacturer guidance on canister orientation during use. Most aerosol sealants are designed for a specific orientation to ensure consistent propellant and product delivery.
Partial use: If you only use part of the canister, replace the cap and store it correctly. Before your next use, check the nozzle for cured sealant and clear it if needed.
Test on a small area: When applying to an unfamiliar surface, test adhesion on a small, inconspicuous area first — a simple step that confirms you'll get the result you're after.

References

Selleys Wet Area Ezi Press – Selleys Australia Product Page (Manufacturer product information)
Safe Work Australia – Globally Harmonised System of Classification and Labelling of Chemicals (GHS) Version 7
Australian Dangerous Goods Code – National Transport Commission
DuluxGroup Australia – Safety Data Sheet Reference SELGHSEN000199, Version 5.0, Issued 23 August 2021 (Manufacturer safety documentation)

Frequently Asked Questions

What is Selleys Wet Area Ezi Press: A pressurised aerosol silicone sealant

Who manufactures Selleys Wet Area Ezi Press: Selleys, a division of DuluxGroup Australia Pty Ltd

What format does Selleys Wet Area Ezi Press come in: Pressurised aerosol canister

What size canister does Selleys Wet Area Ezi Press come in: 100g

Does Selleys Wet Area Ezi Press require a caulking gun: No

What colours is Selleys Wet Area Ezi Press available in: Clear and White

Is Selleys Wet Area Ezi Press suitable for bathrooms: Yes

Is Selleys Wet Area Ezi Press suitable for kitchens: Yes

Is Selleys Wet Area Ezi Press suitable for laundries: Yes

What type of sealant is used in Selleys Wet Area Ezi Press: Silicone sealant

Is Selleys Wet Area Ezi Press suitable for residential use: Yes

Is Selleys Wet Area Ezi Press suitable for trade use: Yes

Is Selleys Wet Area Ezi Press classified as hazardous under GHS: No, classified as non-hazardous

Which GHS version applies to this product: GHS Version 7

Which authority adopted the GHS classification referenced: Safe Work Australia

Is Selleys Wet Area Ezi Press classified as a Dangerous Good: Yes, Class 2.2

What does Dangerous Goods Class 2.2 mean: Non-Flammable, Non-Toxic Gases

Why is it classified as Dangerous Goods Class 2.2: Because it is a pressurised aerosol canister

Is Selleys Wet Area Ezi Press flammable: No

What is the UN number for transporting Selleys Wet Area Ezi Press: UN 1950

What is the proper shipping name for transport: AEROSOLS

What is the air transport designation for this product: NON-FLAMMABLE

What is the maximum storage temperature for Selleys Wet Area Ezi Press: Below 50°C

Should Selleys Wet Area Ezi Press be stored in direct sunlight: No

Should Selleys Wet Area Ezi Press be stored near ignition sources: No

Should Selleys Wet Area Ezi Press be stored near oxidising agents: No

Should Selleys Wet Area Ezi Press be stored in a ventilated area: Yes

Can Selleys Wet Area Ezi Press be stored in a hot car or shed: No

Should the canister be punctured or incinerated: No

Does silicone sealant stay flexible after curing: Yes

Does silicone sealant absorb water: No

Is silicone better than acrylic for wet areas: Yes, for non-porous surfaces

Does silicone sealant adhere to ceramic tiles: Yes

Does silicone sealant adhere to glass: Yes

Does silicone sealant adhere to vitreous enamel: Yes

Can Selleys Wet Area Ezi Press seal bath and shower surrounds: Yes

Can Selleys Wet Area Ezi Press seal sink and basin surrounds: Yes

Can Selleys Wet Area Ezi Press seal splashbacks: Yes

Can Selleys Wet Area Ezi Press seal bathroom window frames: Yes

Is Selleys Wet Area Ezi Press suitable for large commercial sealing projects: No

What canister size is better for large commercial projects: 300ml or 600ml cartridge

Must the surface be dry before applying Selleys Wet Area Ezi Press: Yes

Must the surface be clean before applying Selleys Wet Area Ezi Press: Yes

Must the surface be grease-free before applying: Yes

Should old silicone be removed before applying: Yes

How is old silicone best removed: Using a silicone remover or careful blade tool

How does the aerosol deliver consistent sealant pressure: Pressurised propellant gas inside the canister

Does the aerosol format reduce hand fatigue: Yes

Should the sealant bead be applied in one continuous pass: Yes, where possible

When should the sealant bead be tooled: Promptly, before a skin forms

Can a damp finger be used to tool the bead: Yes

Can masking tape be used for a sharper finish: Yes

When should masking tape be removed: Immediately after tooling

How does silicone sealant cure: Through exposure to atmospheric moisture

Should water contact the sealant before curing is complete: No

Do cold or dry conditions affect curing: Yes, they slow the curing process

What is the recommended joint width for bathroom sealing: 6–10mm

Does applying new sealant over mouldy sealant fix the problem: No

What is the correct solution for mouldy sealant: Full replacement

Does ventilation help prevent mould on sealant: Yes

Should the nozzle be checked before reusing a partial canister: Yes

Is it recommended to test adhesion on an unfamiliar surface first: Yes

Where should the adhesion test be done: On a small, inconspicuous area

Is Selleys Wet Area Ezi Press suitable for beginners: Yes

What is the main advantage of aerosol format over a caulking gun: No separate tool required and consistent pressure

Does the aerosol format eliminate sealant surging: Yes

Is the White colour suitable for most bathroom installations: Yes

When is Clear colour preferred: When substrate colour varies or a less visible seal is needed

What safety precaution applies during application: Work in a ventilated area

Should Selleys Wet Area Ezi Press be kept away from children: Yes

What SDS reference number applies to this product: SELGHSEN000199

What version is the Safety Data Sheet: Version 5.0

When was the Safety Data Sheet issued: 23 August 2021

Label Facts Summary

Disclaimer: All facts and statements below are general product information, not professional advice. Consult relevant experts for specific guidance.

Verified label facts

Product name: Selleys Wet Area Ezi Press
Product type: Pressurised aerosol silicone sealant
Manufacturer: Selleys, a division of DuluxGroup Australia Pty Ltd
Format: Pressurised aerosol canister
Net weight: 100g
Available colours: Clear, White
Intended use areas: Bathrooms, kitchens, laundries (wet areas)
Suitable for: Residential and trade use
Caulking gun required: No
Sealant chemistry: Silicone
GHS hazard classification: Non-hazardous (GHS Version 7, as adopted by Safe Work Australia)
Dangerous Goods classification: Class 2.2 — Non-Flammable, Non-Toxic Gases (Australian Dangerous Goods Code)
Dangerous Goods sub-category: Aerosol Category 3 (non-flammable aerosol)
Flammability: Non-flammable
UN transport number: UN 1950
Proper shipping name: AEROSOLS
Air transport designation: NON-FLAMMABLE
Maximum storage temperature: Below 50°C
Storage requirements: Cool, dry, well-ventilated place; away from direct sunlight, ignition sources, and oxidising agents
Canister must not be: Punctured or incinerated
Adhesion surfaces (label-stated): Ceramic tiles, glass, vitreous enamel
Cure mechanism: Exposure to atmospheric moisture
Safety Data Sheet reference: SELGHSEN000199
SDS version: Version 5.0
SDS issue date: 23 August 2021

General product claims

Aerosol format delivers consistent sealant pressure, reducing hand fatigue compared to a caulking gun
Removes the learning curve associated with controlling a caulking gun
Suitable for DIYers; accessible to beginners
Delivers good results from first use
Silicone formulation stays flexible after curing
Silicone sealant resists water penetration
Silicone handles thermal expansion and contraction in wet environments
Silicone doesn't absorb water and maintains strong adhesion on non-porous surfaces
Silicone outperforms acrylic sealants for wet area applications on non-porous surfaces
Well suited to bath and shower surrounds, sink and basin surrounds, splashbacks, bathroom window frames, and general gap sealing in wet areas
100g canister size suited to small and individual sealing tasks; not recommended for large-scale commercial projects
Recommended joint width for bathroom sealing: 6–10mm
Bead should be tooled promptly before a skin forms
Masking tape applied prior to sealing and removed immediately after tooling produces the sharpest finish
Cold or dry conditions slow the curing process
Applying new sealant over mouldy sealant is not an effective solution; full replacement is recommended
Ventilation during and after sealing helps prevent mould growth on sealant
Adhesion should be tested on a small, inconspicuous area when applying to an unfamiliar surface
Nozzle should be checked and cleared before reusing a partially used canister

Pro Trade Wet Area Silicone - Selleys Product 06 product guide