{
  "id": "web-crawled-products/pro-trade-wet-area-silicone-selleys-product-06",
  "title": "Pro Trade Wet Area Silicone - Selleys Product 06",
  "slug": "web-crawled-products/pro-trade-wet-area-silicone-selleys-product-06",
  "description": "",
  "category": "",
  "content": "## AI Summary\n\n**Product:** Selleys Wet Area Ezi Press\n**Brand:** Selleys (a division of DuluxGroup Australia Pty Ltd)\n**Category:** Pressurised aerosol silicone sealant\n**Primary Use:** Sealing joints and gaps in wet areas such as bathrooms, kitchens, and laundries without a caulking gun.\n\n### Quick Facts\n- **Best For:** DIYers and trade users tackling small to medium wet area sealing jobs in residential settings\n- **Key Benefit:** Aerosol format delivers consistent sealant pressure with no caulking gun required, cutting hand fatigue and skipping the learning curve of manual application\n- **Form Factor:** Pressurised aerosol canister (100g), available in Clear and White\n- **Application Method:** Direct nozzle into joint, press actuator, move steadily along the gap; tool the bead before a skin forms\n\n### Common Questions This Guide Answers\n1. Does Selleys Wet Area Ezi Press require a caulking gun? → No — the pressurised aerosol canister dispenses sealant automatically without any separate applicator tool\n2. Is this product classified as hazardous or dangerous? → Non-hazardous under GHS Version 7 (Safe Work Australia), but classified as Dangerous Goods Class 2.2 (Non-Flammable, Non-Toxic Gases) because it's a pressurised aerosol canister; UN transport number UN 1950\n3. What is the maximum safe storage temperature? → Below 50°C, in a cool, dry, well-ventilated place away from direct sunlight, ignition sources, and oxidising agents\n\n---\n\n## Product Overview\n\nSelleys Wet Area Ezi Press is a pressurised aerosol silicone sealant built for wet area sealing in residential and trade settings. Manufactured by Selleys, a division of DuluxGroup Australia Pty Ltd, it pushes silicone sealant through an aerosol canister — no caulking gun, no fuss. Available in a 100g pressurised canister in Clear and White, it covers the most common aesthetic requirements in kitchens, bathrooms, and laundries.\n\nWhat separates this from traditional tube or cartridge silicone is the delivery mechanism. The aerosol format uses a pressurised canister to dispense sealant at a consistent rate — no separate applicator tool, no manual pressure. It's the practical choice for smaller sealing jobs, touch-up work, and any situation where getting it right the first time matters.\n\n---\n\n## Key Features and What They Mean in Practice\n\n### Aerosol delivery format\n\nThe aerosol canister is the standout feature of Selleys Wet Area Ezi Press, and it changes how you seal. With conventional silicone, you load a cartridge into a caulking gun and apply manual force to push sealant through a nozzle. With this aerosol format, the propellant gas inside the canister does that work — automatically and consistently. The result is steady, even pressure throughout the application, less hand fatigue, and no need to own or maintain a separate caulking gun.\n\nFor DIYers tackling repairs or small sealing jobs, this is a genuine advantage. The learning curve that comes with controlling a caulking gun — avoiding surging, keeping a steady bead — is gone. You get good results from the first use.\n\n### Silicone formulation for wet areas\n\nSelleys Wet Area Ezi Press uses a silicone sealant formulation, which is the right chemistry for wet area applications. Silicone stays flexible after curing, resists water penetration, and handles the thermal expansion and contraction that happens around baths, showers, sinks, and splashbacks. Unlike acrylic sealants, silicone doesn't absorb water and holds strong adhesion on non-porous surfaces including ceramic tiles, glass, and vitreous enamel.\n\nThe wet area designation means this formulation is built specifically for conditions involving regular water exposure, humidity, and cleaning products — the everyday environment of a bathroom or kitchen.\n\n### Available colours\n\nSelleys Wet Area Ezi Press comes in Clear and White. White suits most bathroom and kitchen installations where grout, fixtures, and trims are white. Clear works where a less visible seal is preferred, or where the substrate colour varies and a neutral finish gives the best result. Both options come in the same aerosol format.\n\n---\n\n## Practical Applications and Use Cases\n\nSelleys Wet Area Ezi Press is designed for sealing joints and gaps in wet areas. Typical applications include:\n\n- **Bath and shower surrounds:** Sealing the junction between a bath rim and tiled wall, or around a shower base where it meets the wall, stops water from tracking behind surfaces and causing structural damage or mould growth.\n- **Sink and basin surrounds:** The joint between a sink and benchtop, or between a vanity basin and the wall, is one of the most common points of water ingress in kitchens and bathrooms.\n- **Splashbacks:** Sealing the lower edge of a splashback where it meets a benchtop or cooktop surround keeps moisture out of the substrate and protects surfaces long-term.\n- **Window frames in wet areas:** Bathroom windows often need sealing at the junction with tiled walls, a job this product handles without difficulty.\n- **General gap sealing:** Any gap in a wet area where water could penetrate and where flexibility is needed to accommodate movement.\n\nThe 100g canister size suits these tasks individually or in combination. It's not designed for large-scale commercial sealing projects, where a 300ml or 600ml cartridge would typically be more economical — but for the jobs it's built for, it delivers.\n\n---\n\n## Safety Classification and What It Means\n\nUnderstanding the safety classification of Selleys Wet Area Ezi Press matters for safe handling, storage, and transport. The product carries a dual classification that is sometimes misunderstood.\n\n### Non-hazardous under GHS\n\nThe product is classified as non-hazardous according to the Globally Harmonised System of Classification and Labelling of Chemicals (GHS), Version 7, as adopted by Safe Work Australia. This classification covers health and environmental hazard categories — the product doesn't meet the criteria for being classified as toxic, corrosive, carcinogenic, or environmentally hazardous under this framework.\n\nFor users, this means standard precautions apply: work in a ventilated area, avoid prolonged skin contact, and keep out of reach of children. It doesn't require the elevated handling procedures associated with hazardous chemical products.\n\n### Dangerous Goods Class 2.2\n\nSeparately, the product is classified as Dangerous Goods Class 2.2 (Non-Flammable, Non-Toxic Gases) under the Australian Dangerous Goods Code. This classification applies because the product is an aerosol — the pressurised canister itself, not the sealant chemistry, is the basis for this classification.\n\nAerosol Category 3 under this framework covers non-flammable aerosols. The distinction matters: this product is not flammable in the way that aerosol paints or spray lubricants often are. However, because it's a pressurised container, it remains subject to Dangerous Goods regulations for storage and transport.\n\nThe UN number for transport is UN 1950, with the proper shipping name AEROSOLS. For air transport, the designation is NON-FLAMMABLE. This is relevant for anyone transporting or shipping the product commercially, or for workplaces that need to comply with dangerous goods storage requirements.\n\nFor home users, the practical takeaway is simple: keep the product away from heat sources, open flames, and direct sunlight. Don't puncture or incinerate the canister — standard practice for any aerosol product.\n\n---\n\n## Storage Requirements\n\nStoring Selleys Wet Area Ezi Press correctly preserves both product performance and safety:\n\n- **Temperature:** Store below 50°C. Aerosol canisters are pressure vessels — elevated temperatures increase internal pressure and can cause the canister to rupture or leak. In Australian conditions, this means keeping the product out of vehicles, garden sheds, or anywhere summer temperatures can push past this threshold.\n- **Environment:** Store in a cool, dry, well-ventilated place. Good ventilation matters in the event of any minor propellant gas leakage.\n- **Away from sunlight:** Direct sunlight raises temperature and can degrade the canister over time.\n- **Away from ignition sources:** Even though this product is non-flammable, keeping any pressurised aerosol away from ignition sources is sound practice.\n- **Away from oxidising agents:** Oxidising agents can react with aerosol propellants or sealant components — store them separately.\n\nThese requirements align with Australian Standards for aerosol storage and are consistent with the Dangerous Goods Class 2.2 classification.\n\n---\n\n## Application Guidance\n\n### Surface preparation\n\nGood sealing starts with good preparation. For Selleys Wet Area Ezi Press to perform well, the substrate needs to be:\n\n- **Clean:** Remove existing sealant, soap scum, mould, and cleaning product residue. Old silicone comes off with a silicone remover or a careful blade tool. Any remaining residue will undermine adhesion — take the time to get it right.\n- **Dry:** Silicone sealant needs a dry surface for proper adhesion. Even in a wet area application, the surface must be completely dry at the time of sealing.\n- **Free of grease and dust:** Wipe surfaces with an appropriate cleaner and allow them to dry fully before starting.\n\n### Application\n\nWith the aerosol format, application is straightforward — direct the nozzle into the joint, press the actuator, and move steadily along the gap. A few things to keep in mind:\n\n- Maintain a consistent distance from the surface and a consistent speed to produce an even, clean bead.\n- Apply in a single, continuous pass where possible to avoid joins in the sealant line.\n- The aerosol delivers consistent pressure, but movement speed is in your hands. Move too slowly and you'll get excess sealant; move too quickly and the bead will be incomplete. Find your rhythm and keep it steady.\n\n### Tooling and finishing\n\nOnce the sealant is applied, tool the bead promptly before a skin forms on the surface. A damp finger, a dedicated sealant tool, or a smoothing tool dipped in soapy water presses the sealant into the joint and creates a clean, concave finish. For the sharpest result, apply masking tape to either side of the joint before sealing and pull it away immediately after tooling.\n\n### Curing\n\nSilicone sealants cure through exposure to atmospheric moisture. In a wet area environment, ambient humidity typically supports curing well. Keep the area away from water until curing is complete. Curing time varies depending on temperature, humidity, and bead thickness — check the product packaging for specific cure times. Avoid applying in very cold or very dry conditions, which slow the curing process.\n\n---\n\n## Expert Tips and Best Practices\n\n- **Joint size matters:** Silicone performs best when applied to joints of the right width — not too narrow (which limits adhesion area) and not excessively wide (which can cause the sealant to sag before curing). For most bathroom joints, a bead of 6–10mm is the target.\n- **Mould prevention:** Mould growth on sealant is a common long-term issue in wet areas. Keep the area well-ventilated after sealing and during regular use. When sealant eventually shows mould that can't be cleaned away, the right move is full replacement — not applying new sealant over old.\n- **Canister orientation:** Follow manufacturer guidance on canister orientation during use. Most aerosol sealants are designed for a specific orientation to ensure consistent propellant and product delivery.\n- **Partial use:** If you only use part of the canister, replace the cap and store it correctly. Before your next use, check the nozzle for cured sealant and clear it if needed.\n- **Test on a small area:** When applying to an unfamiliar surface, test adhesion on a small, inconspicuous area first — a simple step that confirms you'll get the result you're after.\n\n---\n\n## References\n\n- [Selleys Wet Area Ezi Press – Selleys Australia Product Page](https://www.selleys.com.au) *(Manufacturer product information)*\n- [Safe Work Australia – Globally Harmonised System of Classification and Labelling of Chemicals (GHS) Version 7](https://www.safeworkaustralia.gov.au/doc/model-work-health-and-safety-regulations)\n- [Australian Dangerous Goods Code – National Transport Commission](https://www.ntc.gov.au/transport-standards/australian-dangerous-goods-code)\n- [DuluxGroup Australia – Safety Data Sheet Reference SELGHSEN000199, Version 5.0, Issued 23 August 2021](https://www.duluxgroup.com.au) *(Manufacturer safety documentation)*\n\n---\n\n## Frequently Asked Questions\n\nWhat is Selleys Wet Area Ezi Press: A pressurised aerosol silicone sealant\n\nWho manufactures Selleys Wet Area Ezi Press: Selleys, a division of DuluxGroup Australia Pty Ltd\n\nWhat format does Selleys Wet Area Ezi Press come in: Pressurised aerosol canister\n\nWhat size canister does Selleys Wet Area Ezi Press come in: 100g\n\nDoes Selleys Wet Area Ezi Press require a caulking gun: No\n\nWhat colours is Selleys Wet Area Ezi Press available in: Clear and White\n\nIs Selleys Wet Area Ezi Press suitable for bathrooms: Yes\n\nIs Selleys Wet Area Ezi Press suitable for kitchens: Yes\n\nIs Selleys Wet Area Ezi Press suitable for laundries: Yes\n\nWhat type of sealant is used in Selleys Wet Area Ezi Press: Silicone sealant\n\nIs Selleys Wet Area Ezi Press suitable for residential use: Yes\n\nIs Selleys Wet Area Ezi Press suitable for trade use: Yes\n\nIs Selleys Wet Area Ezi Press classified as hazardous under GHS: No, classified as non-hazardous\n\nWhich GHS version applies to this product: GHS Version 7\n\nWhich authority adopted the GHS classification referenced: Safe Work Australia\n\nIs Selleys Wet Area Ezi Press classified as a Dangerous Good: Yes, Class 2.2\n\nWhat does Dangerous Goods Class 2.2 mean: Non-Flammable, Non-Toxic Gases\n\nWhy is it classified as Dangerous Goods Class 2.2: Because it is a pressurised aerosol canister\n\nIs Selleys Wet Area Ezi Press flammable: No\n\nWhat is the UN number for transporting Selleys Wet Area Ezi Press: UN 1950\n\nWhat is the proper shipping name for transport: AEROSOLS\n\nWhat is the air transport designation for this product: NON-FLAMMABLE\n\nWhat is the maximum storage temperature for Selleys Wet Area Ezi Press: Below 50°C\n\nShould Selleys Wet Area Ezi Press be stored in direct sunlight: No\n\nShould Selleys Wet Area Ezi Press be stored near ignition sources: No\n\nShould Selleys Wet Area Ezi Press be stored near oxidising agents: No\n\nShould Selleys Wet Area Ezi Press be stored in a ventilated area: Yes\n\nCan Selleys Wet Area Ezi Press be stored in a hot car or shed: No\n\nShould the canister be punctured or incinerated: No\n\nDoes silicone sealant stay flexible after curing: Yes\n\nDoes silicone sealant absorb water: No\n\nIs silicone better than acrylic for wet areas: Yes, for non-porous surfaces\n\nDoes silicone sealant adhere to ceramic tiles: Yes\n\nDoes silicone sealant adhere to glass: Yes\n\nDoes silicone sealant adhere to vitreous enamel: Yes\n\nCan Selleys Wet Area Ezi Press seal bath and shower surrounds: Yes\n\nCan Selleys Wet Area Ezi Press seal sink and basin surrounds: Yes\n\nCan Selleys Wet Area Ezi Press seal splashbacks: Yes\n\nCan Selleys Wet Area Ezi Press seal bathroom window frames: Yes\n\nIs Selleys Wet Area Ezi Press suitable for large commercial sealing projects: No\n\nWhat canister size is better for large commercial projects: 300ml or 600ml cartridge\n\nMust the surface be dry before applying Selleys Wet Area Ezi Press: Yes\n\nMust the surface be clean before applying Selleys Wet Area Ezi Press: Yes\n\nMust the surface be grease-free before applying: Yes\n\nShould old silicone be removed before applying: Yes\n\nHow is old silicone best removed: Using a silicone remover or careful blade tool\n\nHow does the aerosol deliver consistent sealant pressure: Pressurised propellant gas inside the canister\n\nDoes the aerosol format reduce hand fatigue: Yes\n\nShould the sealant bead be applied in one continuous pass: Yes, where possible\n\nWhen should the sealant bead be tooled: Promptly, before a skin forms\n\nCan a damp finger be used to tool the bead: Yes\n\nCan masking tape be used for a sharper finish: Yes\n\nWhen should masking tape be removed: Immediately after tooling\n\nHow does silicone sealant cure: Through exposure to atmospheric moisture\n\nShould water contact the sealant before curing is complete: No\n\nDo cold or dry conditions affect curing: Yes, they slow the curing process\n\nWhat is the recommended joint width for bathroom sealing: 6–10mm\n\nDoes applying new sealant over mouldy sealant fix the problem: No\n\nWhat is the correct solution for mouldy sealant: Full replacement\n\nDoes ventilation help prevent mould on sealant: Yes\n\nShould the nozzle be checked before reusing a partial canister: Yes\n\nIs it recommended to test adhesion on an unfamiliar surface first: Yes\n\nWhere should the adhesion test be done: On a small, inconspicuous area\n\nIs Selleys Wet Area Ezi Press suitable for beginners: Yes\n\nWhat is the main advantage of aerosol format over a caulking gun: No separate tool required and consistent pressure\n\nDoes the aerosol format eliminate sealant surging: Yes\n\nIs the White colour suitable for most bathroom installations: Yes\n\nWhen is Clear colour preferred: When substrate colour varies or a less visible seal is needed\n\nWhat safety precaution applies during application: Work in a ventilated area\n\nShould Selleys Wet Area Ezi Press be kept away from children: Yes\n\nWhat SDS reference number applies to this product: SELGHSEN000199\n\nWhat version is the Safety Data Sheet: Version 5.0\n\nWhen was the Safety Data Sheet issued: 23 August 2021\n\n---\n\n## Label Facts Summary\n\n> **Disclaimer:** All facts and statements below are general product information, not professional advice. Consult relevant experts for specific guidance.\n\n### Verified label facts\n\n- **Product name:** Selleys Wet Area Ezi Press\n- **Product type:** Pressurised aerosol silicone sealant\n- **Manufacturer:** Selleys, a division of DuluxGroup Australia Pty Ltd\n- **Format:** Pressurised aerosol canister\n- **Net weight:** 100g\n- **Available colours:** Clear, White\n- **Intended use areas:** Bathrooms, kitchens, laundries (wet areas)\n- **Suitable for:** Residential and trade use\n- **Caulking gun required:** No\n- **Sealant chemistry:** Silicone\n- **GHS hazard classification:** Non-hazardous (GHS Version 7, as adopted by Safe Work Australia)\n- **Dangerous Goods classification:** Class 2.2 — Non-Flammable, Non-Toxic Gases (Australian Dangerous Goods Code)\n- **Dangerous Goods sub-category:** Aerosol Category 3 (non-flammable aerosol)\n- **Flammability:** Non-flammable\n- **UN transport number:** UN 1950\n- **Proper shipping name:** AEROSOLS\n- **Air transport designation:** NON-FLAMMABLE\n- **Maximum storage temperature:** Below 50°C\n- **Storage requirements:** Cool, dry, well-ventilated place; away from direct sunlight, ignition sources, and oxidising agents\n- **Canister must not be:** Punctured or incinerated\n- **Adhesion surfaces (label-stated):** Ceramic tiles, glass, vitreous enamel\n- **Cure mechanism:** Exposure to atmospheric moisture\n- **Safety Data Sheet reference:** SELGHSEN000199\n- **SDS version:** Version 5.0\n- **SDS issue date:** 23 August 2021\n\n---\n\n### General product claims\n\n- Aerosol format delivers consistent sealant pressure, reducing hand fatigue compared to a caulking gun\n- Removes the learning curve associated with controlling a caulking gun\n- Suitable for DIYers; accessible to beginners\n- Delivers good results from first use\n- Silicone formulation stays flexible after curing\n- Silicone sealant resists water penetration\n- Silicone handles thermal expansion and contraction in wet environments\n- Silicone doesn't absorb water and maintains strong adhesion on non-porous surfaces\n- Silicone outperforms acrylic sealants for wet area applications on non-porous surfaces\n- Well suited to bath and shower surrounds, sink and basin surrounds, splashbacks, bathroom window frames, and general gap sealing in wet areas\n- 100g canister size suited to small and individual sealing tasks; not recommended for large-scale commercial projects\n- Recommended joint width for bathroom sealing: 6–10mm\n- Bead should be tooled promptly before a skin forms\n- Masking tape applied prior to sealing and removed immediately after tooling produces the sharpest finish\n- Cold or dry conditions slow the curing process\n- Applying new sealant over mouldy sealant is not an effective solution; full replacement is recommended\n- Ventilation during and after sealing helps prevent mould growth on sealant\n- Adhesion should be tested on a small, inconspicuous area when applying to an unfamiliar surface\n- Nozzle should be checked and cleared before reusing a partially used canister",
  "geography": {},
  "metadata": {},
  "publishedAt": "",
  "workspaceId": "77ac21fe-85f0-45c0-8279-2da0c52dc749",
  "_links": {
    "canonical": "https://directory.selleys.com.au/web-crawled-products/pro-trade-wet-area-silicone-selleys-product-06/"
  },
  "productInfo": {
    "stock": true
  }
}