{
  "id": "web-crawled-products/selleys-no-more-cracks-plaster-filler-100g-09",
  "title": "Selleys No More Cracks Plaster Filler - 100g 09",
  "slug": "web-crawled-products/selleys-no-more-cracks-plaster-filler-100g-09",
  "description": "",
  "category": "",
  "content": "## AI Summary\n\n**Product:** Selleys No More Cracks RTU Plaster Filler\n**Brand:** Selleys, a division of DuluxGroup Australia Pty Ltd\n**Category:** Interior wall repair compound / plaster filler\n**Primary Use:** Ready-to-use, pre-mixed filler for repairing cracks, holes, and surface imperfections in interior plaster walls and ceilings — no mixing, measuring, or water addition required.\n\n### Quick Facts\n- **Best For:** DIYers and professional tradespeople performing targeted interior plaster repairs (hairline cracks, nail holes, screw holes, surface chips, minor settlement cracks)\n- **Key Benefit:** Zero preparation time — factory pre-mixed to exact working consistency; open container and apply immediately\n- **Form Factor:** White paste, 100g sealed container\n- **Application Method:** Apply directly from container using a flexible filling knife; press firmly into void; leave slightly proud of surface; sand smooth with 120–180 grit sandpaper once fully dry\n\n### Common Questions This Guide Answers\n1. Does Selleys No More Cracks RTU require mixing or water? No — RTU (Ready to Use) means no mixing, no water, and no measuring required\n2. Is this product safe to transport and store without special handling? Yes — not classified as a hazardous substance or Dangerous Goods for transport by road, rail, sea, or air in Australia and New Zealand\n3. What PPE is required when using this product? Nitrile rubber gloves (during active handling), safety glasses, overalls, and safety shoes, per SDS Version 5.0 issued 20 October 2025\n4. Can deep repairs be filled in a single application? No — repairs deeper than approximately 5mm should be built up in multiple layers, allowing each layer to dry fully before applying the next\n5. Why does the painted surface look patchy after repair? Filler absorbs paint differently to surrounding plaster; apply a primer or mist coat over the repaired area before full painting to ensure a uniform finish\n\n---\n\n## Selleys No More Cracks RTU Plaster Filler — complete product guide\n\n## Product overview\n\nSelleys No More Cracks RTU Plaster Filler is a ready-mixed interior wall repair compound for filling cracks, holes, and surface imperfections in plaster walls and ceilings. Manufactured by Selleys, a division of DuluxGroup Australia Pty Ltd, it has a long track record in the Australian home repair market and works equally well for tradespeople and first-time DIYers.\n\nThe product comes in a 100g container — a white paste with a mild characteristic odour. Its main practical advantage is zero preparation time. No powder to mix, no water to add, no waiting around to get the consistency right. Open the container and apply directly to the surface.\n\nThis guide covers everything you need to use Selleys No More Cracks RTU Plaster Filler safely and effectively — from understanding what the product is, to applying it with precision and storing it properly for the next job.\n\n---\n\n## What \"Ready to Use\" actually means\n\nRTU stands for Ready to Use, and understanding this matters for getting good results from the first application. Many plaster fillers are sold as dry powder that must be measured and mixed with water before use. That process introduces variables — too much water produces a runny, weak filler; too little makes it hard to spread and prone to cracking as it dries.\n\nSelleys No More Cracks RTU cuts out that uncertainty entirely. The filler is pre-mixed at the factory to the exact working consistency and supplied in a sealed container. Open it, and the product is ready to go.\n\nFor any user — professional or first-timer — this means no guesswork around mixing ratios, no wasted material from failed mixes, and a faster start, which is particularly useful for small incidental repairs that need to look perfect.\n\nThe 100g size suits targeted, precise repairs rather than large-scale filling jobs, where a bulk powder product may be more economical. For minor repairs, it's the practical, high-quality choice.\n\n---\n\n## Intended surface and application scope\n\nSelleys No More Cracks RTU Plaster Filler is formulated for interior plaster surfaces. It is not designed for exterior use, and applying it outdoors or in moisture-exposed areas — bathrooms or laundries, for example — falls outside its intended scope.\n\nTypical applications include:\n\n- Hairline cracks in plaster walls or ceilings\n- Small holes left by nails, screws, or picture hooks\n- Surface chips and gouges in plaster\n- Minor settlement cracks in interior plaster\n\nThe 100g container reflects the product's purpose: precise, targeted repairs rather than whole-wall resurfacing. For context, 100g of paste filler covers multiple small nail holes or a short run of hairline cracking with ease, leaving a clean, invisible repair.\n\n---\n\n## How to apply Selleys No More Cracks RTU Plaster Filler\n\n### Surface preparation\n\nA quality repair starts with a clean surface. Before applying filler, make sure the surface is clean, dry, and free from loose material. For cracks, use a scraper or filling knife edge to remove any flaking plaster or paint around the crack edges, then brush out dust and debris from inside the crack. A properly prepared surface gives the filler something solid to bond to — no lifting, no shrinking away from edges as it dries.\n\n### Application method\n\nApply the filler directly from the container using a flexible filling knife or putty knife. Work it firmly into the crack or hole, pressing to fill the full depth of the void. For deeper repairs, build up the filler in layers rather than attempting to fill the full depth in a single pass — thick single applications increase the risk of cracking or shrinkage as the product cures.\n\nDraw the filling knife across the surface at a slight angle, leaving the filler marginally proud — raised slightly above the surrounding wall surface. This accounts for the minor shrinkage that occurs during drying and sets you up for a flush finish after sanding.\n\n### Drying and finishing\n\nAllow the filler to dry fully before sanding. Drying time varies depending on the depth of the repair, ambient temperature, and humidity. Once dry, sand smooth with fine-grit sandpaper — 120 to 180 grit — until the repair is flush with the surrounding surface. Wipe away dust before painting.\n\nFor deeper repairs requiring a second coat, let the first coat dry completely before applying the next layer. That patience pays off in the final result.\n\n---\n\n## Safety considerations and required PPE\n\nSelleys No More Cracks RTU Plaster Filler is not classified as a hazardous substance or Dangerous Goods for transport by road, rail, sea, or air in Australia and New Zealand. That said, using appropriate personal protective equipment is standard practice.\n\nThe manufacturer's Safety Data Sheet (SDS) specifies the following PPE:\n\n| PPE Item | Purpose |\n|---|---|\n| Safety shoes | Protection against dropped containers or tools |\n| Overalls | Skin and clothing protection during application |\n| Nitrile rubber gloves (for intermittent contact) | Hand protection when handling the product |\n| Safety glasses | Eye protection against splashes during application |\n\n### Understanding \"intermittent contact\" for gloves\n\nThe SDS specifies nitrile rubber gloves for intermittent contact — meaning gloves are recommended whenever you are actively handling the product. The risk associated with brief or incidental skin contact is low, but wearing the right gear is always the sensible call. Nitrile rubber resists a wide range of chemicals and provides reliable barrier protection for this type of task.\n\n### Ventilation\n\nThe product has only a mild characteristic odour and carries no hazardous classification. Working in a well-ventilated space is still the sensible standard when using any filler or coating product indoors.\n\n### Non-Dangerous Goods classification\n\nThe confirmation that this product is not classified as Dangerous Goods under Australian and New Zealand transport regulations is relevant for tradespeople and retailers managing storage and transport. No special handling, labelling, or transport restrictions apply — just standard safe handling practices.\n\n---\n\n## Storage and product care\n\nSeal the container tightly after every use. Exposure to air causes the paste surface to dry out and form a skin, which can affect smooth application next time.\n\nKey storage guidance:\n\n- Seal the container immediately after use\n- Store in a cool, dry location away from direct sunlight and heat sources\n- Keep out of reach of children\n- Do not allow the product to freeze — freezing can alter the consistency and affect performance\n\nIf a skin forms on the surface after storage, it can often be removed carefully with a spatula, with usable product beneath. If the product has dried significantly throughout the container, replace it. Starting fresh ensures the quality of your repair holds up.\n\n---\n\n## Tips for better results\n\nThese are the techniques that separate a good repair from one that's invisible once painted.\n\n**Build depth in layers, not one pass.** For any repair deeper than approximately 5mm, apply two or more layers, allowing each to dry fully. This eliminates cracking and shrinkage and produces a repair that lasts.\n\n**Dampen very dry or porous plaster** before applying filler. This slows moisture absorption from the filler into the wall, giving the product more time to bond and reducing the risk of it drying too fast.\n\n**Use a flexible filling knife.** Flexibility gives you control — it lets you feather the edges of the repair cleanly, making the final sanding stage faster and the result sharper.\n\n**Sand lightly between coats** when applying multiple layers. A light pass with fine-grit paper between coats helps the next layer bond smoothly and evenly to the first.\n\n**Prime before painting.** Filler absorbs paint differently to surrounding plaster, which can create a patchy finish. A coat of primer or diluted paint — a mist coat — over the repaired area before full painting ensures a consistent result across the whole wall.\n\n**Work in moderate temperatures.** Very cold or very hot conditions affect drying time and final finish. Consistent results come from working between 10°C and 30°C.\n\n---\n\n## Troubleshooting common issues\n\nEven with the right product, surfaces can present their own challenges. Here's how to handle the most common ones.\n\n### The filler is cracking as it dries\n\nThe repair was likely too deep for a single application, or the filler dried too fast on a very dry or porous surface. Let the cracked filler dry fully, remove any loose material, and re-apply in thinner, controlled layers.\n\n### The filler is shrinking below the wall surface\n\nMinor shrinkage is a normal part of the drying process. Apply a second thin coat once the first has dried fully, building the repair back up to flush or slightly proud of the surface, then sand smooth.\n\n### The filler won't sand smoothly\n\nCheck that the filler is completely dry before sanding. Sanding while the filler is still damp tears the surface rather than abrading it cleanly. If the filler is dry but still resisting, start with a slightly coarser grit — around 80 to 100 — before finishing with fine grit.\n\n### The surface looks patchy after painting\n\nThis usually comes from painting directly over filler without a primer coat. Sand the area lightly, apply a primer or mist coat over the repair, and repaint.\n\n---\n\n## References\n\n- [Selleys No More Cracks Product Page — Selleys Australia](https://www.selleys.com.au/fillers/no-more-cracks/)\n- [Selleys No More Cracks RTU Plaster Filler Safety Data Sheet (SDS) — DuluxGroup / Selleys, Version 5.0, Issued 20 October 2025](https://www.selleys.com.au/)\n- [Safe Work Australia — Guidance on Safety Data Sheets and Hazardous Chemicals](https://www.safeworkaustralia.gov.au/chemicals/safety-data-sheets)\n- [Australian Dangerous Goods Code (ADG Code) — Transport and Infrastructure](https://www.ntc.gov.au/transport-standards/australian-dangerous-goods-code)\n\n---\n\n## Frequently asked questions\n\nWhat is Selleys No More Cracks RTU Plaster Filler: A ready-to-use interior wall repair compound\n\nWho manufactures Selleys No More Cracks RTU: Selleys, a division of DuluxGroup Australia Pty Ltd\n\nWhat does RTU stand for: Ready to Use\n\nDoes RTU mean no mixing is required: Yes, no mixing required\n\nDoes it require water to be added: No, no water needed\n\nDoes it require measuring before use: No, no measuring required\n\nWhat colour is the product: White paste\n\nWhat is the container size: 100g\n\nWhat is the odour of the product: Mild characteristic odour\n\nIs it suitable for interior use: Yes, interior use only\n\nIs it suitable for exterior use: No, not formulated for exterior use\n\nIs it suitable for bathroom use: No, not for moisture-exposed areas\n\nIs it suitable for laundry areas: No, not for moisture-exposed areas\n\nWhat surfaces is it designed for: Interior plaster walls and ceilings\n\nCan it fill hairline cracks: Yes\n\nCan it fill nail holes: Yes\n\nCan it fill screw holes: Yes\n\nCan it fill picture hook holes: Yes\n\nCan it fill surface chips in plaster: Yes\n\nCan it fill minor settlement cracks: Yes\n\nIs it suitable for whole-wall resurfacing: No, designed for targeted repairs\n\nDoes it require surface preparation before application: Yes\n\nWhat surface preparation is required: Surface must be clean, dry, and free from loose material\n\nShould loose plaster be removed before applying: Yes\n\nWhat tool is recommended for application: A flexible filling knife or putty knife\n\nShould filler be pressed firmly into the crack: Yes, press firmly to fill full depth\n\nShould the filler be applied flush or proud of the surface: Slightly proud of the surface\n\nWhy should filler be left slightly proud: To account for minor shrinkage during drying\n\nCan deep repairs be filled in a single pass: No, build up in layers\n\nWhat is the recommended maximum single-layer depth: Approximately 5mm\n\nShould each layer dry before applying the next: Yes, fully dry between layers\n\nShould the filler be sanded after drying: Yes\n\nWhat sandpaper grit is recommended for finishing: 120 to 180 grit fine sandpaper\n\nShould dust be wiped away before painting: Yes\n\nShould a primer be applied before painting: Yes, recommended before painting\n\nWhy is priming recommended over filler: Filler absorbs paint differently to surrounding plaster\n\nWhat is a mist coat: A diluted paint coat applied before full painting\n\nDoes the product need to be primed to avoid patchiness: Yes\n\nIs the product classified as a hazardous substance: No\n\nIs it classified as Dangerous Goods for transport: No\n\nDoes the non-hazardous classification apply to road transport: Yes\n\nDoes the non-hazardous classification apply to sea transport: Yes\n\nDoes the non-hazardous classification apply to air transport: Yes\n\nDoes the non-hazardous classification apply to rail transport: Yes\n\nIs PPE required when using the product: Yes, PPE is recommended\n\nWhat gloves are recommended: Nitrile rubber gloves\n\nWhen are gloves recommended: During active handling of the product\n\nAre safety glasses required: Yes\n\nAre overalls recommended: Yes\n\nAre safety shoes recommended: Yes\n\nWhat is the purpose of safety glasses during use: Protection against splashes\n\nIs ventilation required during use: Yes, work in a well-ventilated space\n\nHow should the container be stored after use: Sealed tightly\n\nWhere should the product be stored: Cool, dry location away from sunlight and heat\n\nShould the product be kept away from children: Yes\n\nCan the product be allowed to freeze: No, freezing alters consistency\n\nWhat happens if a skin forms on the stored product: Remove carefully with a spatula\n\nWhen should the product be replaced: If dried significantly throughout the container\n\nWhat causes filler to crack during drying: Repair too deep for a single application\n\nWhat else causes filler to crack during drying: Filler drying too fast on a porous surface\n\nHow to fix cracking filler: Remove loose material and re-apply in thinner layers\n\nIs minor shrinkage below the wall surface normal: Yes\n\nHow to fix shrinkage below wall surface: Apply a second thin coat once first coat is dry\n\nWhy does filler resist smooth sanding: Filler may still be damp\n\nWhat grit sandpaper to start with on resistant filler: 80 to 100 grit\n\nWhat causes a patchy finish after painting over filler: Painting directly over filler without primer\n\nHow to fix a patchy painted finish: Sand lightly, apply primer, then repaint\n\nShould very dry or porous plaster be dampened before filling: Yes\n\nWhy dampen porous plaster before filling: Slows moisture absorption from filler into wall\n\nWhat type of filling knife delivers best results: A flexible filling knife\n\nShould layers be sanded between coats: Yes, lightly sand between coats\n\nWhat is the ideal working temperature range: Between 10°C and 30°C\n\nDoes very cold temperature affect drying: Yes, affects drying time and finish\n\nDoes very hot temperature affect drying: Yes, affects drying time and finish\n\nWhat country is this product primarily marketed in: Australia\n\nIs this product suitable for first-time DIYers: Yes\n\nIs this product suitable for professional tradespeople: Yes\n\nWhat SDS version covers this product: Version 5.0\n\nWhen was the current SDS issued: 20 October 2025\n\n---\n\n## Label facts summary\n\n> **Disclaimer:** All facts and statements below are general product information, not professional advice. Consult relevant experts for specific guidance.\n\n### Verified label facts\n\n- **Product name:** Selleys No More Cracks RTU Plaster Filler\n- **Manufacturer:** Selleys, a division of DuluxGroup Australia Pty Ltd\n- **RTU designation:** Ready to Use — no mixing, no water addition, no measuring required\n- **Container size:** 100g\n- **Form/colour:** White paste\n- **Odour:** Mild characteristic odour\n- **Intended use:** Interior plaster walls and ceilings only\n- **Not suitable for:** Exterior use, bathrooms, laundry areas, or moisture-exposed areas\n- **Hazardous substance classification:** Not classified as a hazardous substance\n- **Dangerous Goods classification:** Not classified as Dangerous Goods for transport by road, rail, sea, or air (Australia and New Zealand)\n- **Recommended PPE (per SDS):** Nitrile rubber gloves (intermittent contact), safety glasses, overalls, safety shoes\n- **Glove use timing:** During active handling of the product\n- **Ventilation requirement:** Work in a well-ventilated space\n- **Storage:** Seal tightly after use; store in a cool, dry location away from direct sunlight and heat sources; keep out of reach of children; do not allow to freeze\n- **Application tool:** Flexible filling knife or putty knife\n- **Application method:** Apply directly from container; press firmly into full depth of void; leave slightly proud of surface\n- **Layer depth guidance:** Build up repairs deeper than approximately 5mm in multiple layers; allow each layer to dry fully before applying the next\n- **Finishing sandpaper grit:** 120 to 180 grit fine sandpaper\n- **Primer recommendation:** Apply primer or mist coat over repair before full painting\n- **Ideal working temperature range:** 10°C to 30°C\n- **SDS version:** Version 5.0\n- **SDS issue date:** 20 October 2025\n- **Primary market:** Australia\n\n### General product claims\n\n- Delivers professional wall repair results\n- Eliminates mixing uncertainty by supplying pre-mixed filler at the factory\n- 100g size is suited to targeted, precise repairs rather than large-scale filling jobs\n- Suitable for first-time DIYers and professional tradespeople\n- A flexible filling knife gives better control and cleaner feathered edges\n- Dampening very dry or porous plaster before application slows moisture absorption and improves bonding\n- Lightly sanding between coats improves adhesion of subsequent layers\n- Applying a mist coat before full painting ensures a consistent finish\n- Minor shrinkage below the wall surface during drying is a normal part of the process\n- If a skin forms on stored product, usable filler may remain beneath and can be recovered with a spatula",
  "geography": {},
  "metadata": {},
  "publishedAt": "",
  "workspaceId": "77ac21fe-85f0-45c0-8279-2da0c52dc749",
  "_links": {
    "canonical": "https://directory.selleys.com.au/web-crawled-products/selleys-no-more-cracks-plaster-filler-100g-09/"
  },
  "productInfo": {
    "stock": true
  },
  "productFeedItemId": "de463897-c7d7-4421-a8ae-1f6442b2ac82"
}