{
  "id": "web-crawled-products/selleys-auto-fix-windscreen-sealant-black-100ml-07",
  "title": "Selleys Auto Fix Windscreen Sealant Black - 100mL 07",
  "slug": "web-crawled-products/selleys-auto-fix-windscreen-sealant-black-100ml-07",
  "description": "",
  "category": "",
  "content": "## AI Summary\n\n**Product:** Selleys Auto Fix Supa Glue\n**Brand:** Selleys (a division of DuluxGroup Australia Pty Ltd)\n**Category:** Cyanoacrylate Adhesive (Super Glue)\n**Primary Use:** Fast-acting ethyl cyanoacrylate adhesive for high-strength bonding of metals, ceramics, plastics, rubber, and glass across repair and assembly tasks.\n\n### Quick Facts\n- **Best For:** Tradespeople and everyday DIYers who need reliable, load-bearing bonds without specialised equipment\n- **Key Benefit:** Rapid moisture-activated cure with initial handling strength in 1–2 minutes and no clamping required for most small repairs\n- **Form Factor:** Clear liquid in a compact 3 ml tube\n- **Application Method:** Apply one drop per 1–2 cm² to one surface only, press and hold for 30–60 seconds\n\n### Common Questions This Guide Answers\n1. What is the primary ingredient in Selleys Auto Fix Supa Glue? → Ethyl cyanoacrylate (CAS 7085-85-0) at greater than 60% w/w\n2. Is this product classified as Dangerous Goods for transport? → No — not classified under road, rail, IMDG (sea), or IATA (air) regulations\n3. What should you do if the adhesive contacts your eyes? → Flush continuously with running water for a minimum of 15 minutes and seek immediate medical attention; do not force open a bonded eyelid\n\n---\n\n## Product Overview\n\nSelleys Auto Fix Supa Glue is a fast-acting cyanoacrylate adhesive built for reliable bonding across a wide range of repair and assembly tasks. Manufactured by Selleys, a division of DuluxGroup Australia Pty Ltd, it delivers strong bonding performance for tradespeople and everyday DIYers alike — no complex preparation, no specialised equipment required.\n\nThe adhesive comes in a compact 3 ml tube and produces a clear, liquid bond that cures rapidly on contact with surface moisture. Understanding what this product contains, how it works, and how to use it safely is the difference between a bond that holds and one that doesn't — so here's everything you need.\n\n---\n\n## What Is Selleys Auto Fix Supa Glue?\n\nSelleys Auto Fix Supa Glue is an ethyl cyanoacrylate adhesive — the chemical family behind what most people call \"super glue.\" The product reference number is SELGHSEN000017, and the current Safety Data Sheet (SDS) was issued 3 June 2022 (Version 8.0), confirming this is an actively maintained, current formulation.\n\n### Active ingredient: Ethyl cyanoacrylate\n\nThe primary ingredient is **ethyl cyanoacrylate** (CAS 7085-85-0), present at greater than 60% w/w. This compound is responsible for the adhesive's bonding performance. Ethyl cyanoacrylate polymerises — forming long molecular chains — almost instantly when it encounters even trace amounts of moisture, including the humidity naturally present on most surfaces and in ambient air. That reaction is what creates the fast set and high-strength bond.\n\nAt greater than 60% concentration, ethyl cyanoacrylate is the dominant component of the formulation, not a minor additive. That's consistent with a cyanoacrylate product built for reliable, load-bearing bonds rather than temporary fixes.\n\n### Stabiliser: Hydroquinone\n\nThe secondary ingredient is **hydroquinone** (CAS 123-31-9), present at less than 0.2% w/w. Hydroquinone is a polymerisation inhibitor — it prevents the adhesive from curing prematurely inside the tube during storage. Without it, the ethyl cyanoacrylate could begin reacting with ambient moisture before it ever reaches the intended surface.\n\nAlthough hydroquinone is present in a very small quantity, it is a classified hazardous substance and contributes to the product's overall hazard profile. This is why the product is classified as hazardous under Australian safety standards, even though it is not classified as Dangerous Goods for transport purposes — see the Safety section below for full details.\n\n### Physical form\n\nThe adhesive is a clear liquid, curing to an essentially invisible bond line on most surfaces. That makes it a practical choice for applications where appearance matters — repairs to transparent or light-coloured materials, for instance — as well as standard structural bonding tasks where a clean finish is the goal.\n\n---\n\n## Key Features and What They Mean in Practice\n\n### High-strength bonding\n\nThe ethyl cyanoacrylate formulation produces a bond that stands up to significant mechanical stress once fully cured. Cyanoacrylate adhesives perform best in thin film applications — the thinner the glue layer, the stronger the bond. Applying too much product works against you: thick layers cure more slowly and unevenly, producing a brittle result rather than a rigid, load-bearing joint.\n\n### Fast cure\n\nEthyl cyanoacrylate cures on contact with moisture. Initial tack forms within seconds, and handling strength is typically achieved within a minute or two, depending on surface material, joint fit, and ambient humidity. Full cure strength develops over 24 hours. This speed eliminates the need for clamping or extended drying time for most small repairs.\n\n### Clear finish\n\nBecause the cured adhesive is transparent, the bond line stays minimally visible on most surfaces. This is particularly useful when repairing items where appearance counts — ceramics, glass, or light-coloured plastics.\n\n### Compact 3 ml format\n\nThe 3 ml tube is sized for targeted, controlled application. Cyanoacrylate adhesives work in small quantities — a single drop is often enough for a bond area of several square centimetres. The compact format reduces waste, makes the product easy to store and handle, and keeps accidental spills or skin contact manageable.\n\n---\n\n## Practical Applications\n\nSelleys Auto Fix Supa Glue works well across a range of non-porous and semi-porous materials, including:\n\n- **Metals** — small brackets, jewellery, tooling repairs\n- **Ceramics and porcelain** — broken tiles, crockery, figurines\n- **Hard plastics** — ABS, acrylic, polystyrene components\n- **Rubber** — seals, gaskets, flexible components\n- **Glass** — small cracks, broken decorative items\n\nCyanoacrylate adhesives are generally less effective on highly porous materials such as untreated wood or foam, because the adhesive absorbs into the substrate before it can form a surface bond. They also perform poorly on polyethylene, polypropylene, and PTFE (Teflon) surfaces, which have low surface energy and resist adhesion from most adhesive types.\n\nFor best results, surfaces need to be clean, dry, and closely fitting. The closer the fit between two surfaces, the thinner the glue film — and the stronger the resulting bond.\n\n---\n\n## How to Use Selleys Auto Fix Supa Glue\n\n### Surface preparation\n\nClean both surfaces thoroughly before applying the adhesive. Remove grease, oil, dust, and any previous adhesive residue. On metal surfaces, light sanding or abrasion improves adhesion by increasing surface area. Dry surfaces completely — while ethyl cyanoacrylate needs surface moisture to cure, excess water causes it to cure too rapidly and produces a foamy, weakened bond.\n\n### Application\n\nApply a small amount of adhesive to one surface only. A single drop is typically enough for a bond area of 1–2 square centimetres. Applying more does not improve bond strength — it extends cure time and increases the risk of squeeze-out onto surrounding surfaces or skin.\n\nPress the two surfaces together firmly and hold for 30–60 seconds. Keep the joint still during this initial cure period. Any movement before the adhesive has set will undermine the bond.\n\n### Cure time\n\nInitial handling strength develops in 1–2 minutes, though this varies by substrate and conditions. Full cure takes 24 hours — allow that time before subjecting the bond to full load or stress.\n\nHigher humidity accelerates cure. Lower humidity and low-porosity surfaces such as smooth metal or glass may extend initial set time slightly.\n\n### Tube care after use\n\nWipe the nozzle clean immediately after use and replace the cap firmly. Cyanoacrylate adhesive will cure inside the nozzle if exposed to air moisture, blocking the tube. Storing the capped tube in a sealed plastic bag limits moisture exposure further and extends shelf life.\n\n---\n\n## Safety Considerations\n\n### Hazard classification\n\nSelleys Auto Fix Supa Glue is classified as hazardous under Australian workplace health and safety regulations. This classification is primarily due to the presence of hydroquinone, even at sub-0.2% concentrations, combined with the irritant and bonding properties of ethyl cyanoacrylate itself.\n\nThe product is not classified as Dangerous Goods under any transport mode:\n\n- Not classified under road or rail transport standards\n- Not classified under IMDG (International Maritime Dangerous Goods) for sea transport\n- Not classified under IATA (International Air Transport Association) for air transport\n\nThis distinction matters practically: the product can be shipped without the special handling requirements that apply to dangerous goods, so it's straightforward to purchase and receive by standard delivery.\n\n### Skin contact\n\nEthyl cyanoacrylate bonds skin rapidly — often faster than it bonds the intended substrate, because skin provides an ideal moisture-rich surface for polymerisation. If skin contact occurs:\n\n- Do not attempt to pull bonded skin apart forcibly, as this can cause tearing\n- Soak the bonded area in warm soapy water and gently peel or roll the skin apart\n- Acetone (nail polish remover) can help dissolve cured cyanoacrylate from skin\n- If irritation persists or skin is damaged, seek medical advice\n\nIf the adhesive contacts eyes, flush continuously with running water for a minimum of 15 minutes and transport the affected person to a doctor or hospital immediately. Do not attempt to open a bonded eyelid by force.\n\n### Skin and respiratory irritation\n\nEthyl cyanoacrylate vapour can irritate the eyes, nose, and throat, particularly in enclosed spaces. Always use the product in a well-ventilated area. Prolonged or repeated exposure to vapour is not recommended without appropriate respiratory protection.\n\n### Ingestion\n\nIf swallowed, do not induce vomiting. Seek immediate medical attention. The cyanoacrylate may bond to oral and gastrointestinal tissues.\n\n### First aid summary\n\n| Exposure Route | First Aid Action |\n|---|---|\n| Skin contact | Soak in warm soapy water; do not force apart bonded skin |\n| Eye contact | Flush with running water for 15+ minutes; seek medical attention |\n| Inhalation | Move to fresh air; seek medical attention if symptoms persist |\n| Ingestion | Do not induce vomiting; seek immediate medical attention |\n\n---\n\n## Storage and Shelf Life\n\nStore Selleys Auto Fix Supa Glue in a cool, dry location away from direct sunlight and heat sources. Elevated temperatures and humidity accelerate the degradation of cyanoacrylate adhesives in storage, causing them to thicken and eventually cure inside the tube.\n\nKeep the product away from children and pets. The small tube format reduces but does not eliminate the risk of accidental ingestion or skin contact.\n\nStore the product separately from oxidising agents and alkaline materials, which can react with ethyl cyanoacrylate or accelerate its polymerisation.\n\n---\n\n## Tips for Best Results\n\nSelleys has been in the business for over 80 years, and a few practical lessons come up repeatedly with cyanoacrylate adhesives:\n\n- **Less is more.** The most common mistake is applying too much. A thin, even film produces a stronger bond than a thick one, every time.\n- **Surface fit matters.** Gaps weaken cyanoacrylate bonds significantly. If surfaces don't fit closely, a gap-filling adhesive is a better choice for that job.\n- **Temperature affects cure.** Cool surfaces slow cure; warm surfaces and high humidity speed it up. Room temperature gives the most consistent results.\n- **Accelerators are available.** Separate cyanoacrylate accelerator sprays reduce cure time on demanding substrates — useful in low-humidity conditions or with low-porosity materials.\n- **Debonders exist.** Acetone-based cyanoacrylate debonders can dissolve cured adhesive when repositioning is needed, though acting before full cure is always easier.\n- **Keep the nozzle clear.** Never touch the nozzle to surfaces. Apply to one surface, then bring the other into contact. It's a simple habit that keeps the tube usable job after job.\n\n---\n\n## References\n\n- [Selleys Auto Fix Supa Glue Safety Data Sheet (SDS) — SELGHSEN000017, Version 8.0, 3 June 2022](https://www.selleys.com.au) *(Based on manufacturer documentation provided; verify current SDS at Selleys official site)*\n- [DuluxGroup Australia Pty Ltd — Selleys Brand](https://www.duluxgroup.com.au)\n- [Safe Work Australia — Hazardous Chemicals Information](https://www.safeworkaustralia.gov.au/chemicals)\n- [IATA Dangerous Goods Regulations — Classification Reference](https://www.iata.org/en/programs/cargo/dgr/)\n- [IMDG Code — International Maritime Dangerous Goods](https://www.imo.org/en/OurWork/Safety/Pages/DangerousGoods-default.aspx)\n\n## Frequently Asked Questions\n\nWhat is Selleys Auto Fix Supa Glue: A fast-acting cyanoacrylate adhesive\n\nWho manufactures Selleys Auto Fix Supa Glue: Selleys, a division of DuluxGroup Australia Pty Ltd\n\nWhat is the product reference number: SELGHSEN000017\n\nWhat is the SDS version number: Version 8.0\n\nWhen was the current SDS issued: 3 June 2022\n\nWhat is the primary active ingredient: Ethyl cyanoacrylate\n\nWhat is the CAS number for ethyl cyanoacrylate: 7085-85-0\n\nWhat concentration is ethyl cyanoacrylate present at: Greater than 60% w/w\n\nWhat is the secondary ingredient: Hydroquinone\n\nWhat is the CAS number for hydroquinone: 123-31-9\n\nWhat concentration is hydroquinone present at: Less than 0.2% w/w\n\nWhat role does hydroquinone play: It prevents premature curing during storage\n\nWhat is the physical form of the adhesive: Clear liquid\n\nWhat volume does the tube contain: 3 ml\n\nWhat colour is the cured bond: Clear and essentially invisible\n\nHow does ethyl cyanoacrylate cure: It polymerises on contact with moisture\n\nDoes it require heat to cure: No, it cures at room temperature\n\nDoes it require UV light to cure: No\n\nWhat triggers the curing reaction: Trace moisture on surfaces or in ambient air\n\nWhat is the initial handling strength time: 1–2 minutes\n\nWhat is the full cure time: 24 hours\n\nDoes higher humidity speed up cure: Yes\n\nDoes lower humidity slow cure: Yes\n\nShould you apply adhesive to both surfaces: No, apply to one surface only\n\nHow much adhesive should be applied per bond: One drop per 1–2 square centimetres\n\nDoes applying more adhesive improve bond strength: No, it weakens the bond\n\nWhat happens if too much adhesive is applied: Cure is slower and the bond becomes brittle\n\nHow long should surfaces be held together after application: 30–60 seconds\n\nDoes the bond require clamping: No, for most small repairs\n\nIs surface preparation required: Yes\n\nWhat should be removed from surfaces before bonding: Grease, oil, dust, and old adhesive residue\n\nDoes metal benefit from sanding before bonding: Yes, light abrasion improves adhesion\n\nCan excess water on surfaces cause problems: Yes, it causes foamy, weakened bonds\n\nIs this product suitable for bonding metals: Yes\n\nIs this product suitable for bonding ceramics: Yes\n\nIs this product suitable for bonding porcelain: Yes\n\nIs this product suitable for bonding hard plastics: Yes\n\nIs this product suitable for bonding rubber: Yes\n\nIs this product suitable for bonding glass: Yes\n\nIs this product suitable for bonding polyethylene: No\n\nIs this product suitable for bonding polypropylene: No\n\nIs this product suitable for bonding PTFE (Teflon): No\n\nIs this product suitable for highly porous materials like untreated wood: Generally no\n\nDoes a closer surface fit produce a stronger bond: Yes\n\nIs this product classified as hazardous: Yes, under Australian WHS regulations\n\nWhat makes it hazardous: Presence of hydroquinone and irritant properties of ethyl cyanoacrylate\n\nIs this product classified as Dangerous Goods for road transport: No\n\nIs this product classified as Dangerous Goods for rail transport: No\n\nIs this product classified as Dangerous Goods under IMDG for sea transport: No\n\nIs this product classified as Dangerous Goods under IATA for air transport: No\n\nCan it be shipped by standard delivery: Yes\n\nDoes ethyl cyanoacrylate bond skin quickly: Yes, often faster than intended substrates\n\nShould bonded skin be pulled apart forcibly: No\n\nHow should bonded skin be treated: Soak in warm soapy water and gently peel apart\n\nCan acetone remove cured adhesive from skin: Yes\n\nWhat should be done if adhesive contacts eyes: Flush with running water for minimum 15 minutes\n\nShould a bonded eyelid be forced open: No\n\nShould you seek medical attention after eye contact: Yes, immediately\n\nWhat should be done if adhesive is inhaled: Move to fresh air\n\nShould you seek medical attention after inhalation symptoms persist: Yes\n\nShould vomiting be induced if adhesive is swallowed: No\n\nWhat should be done if adhesive is swallowed: Seek immediate medical attention\n\nCan cyanoacrylate vapour cause irritation: Yes, to eyes, nose, and throat\n\nShould the product be used in enclosed spaces: No, use in well-ventilated areas only\n\nShould the product be kept away from children: Yes\n\nShould the product be kept away from pets: Yes\n\nWhere should the product be stored: Cool, dry location away from sunlight and heat\n\nShould the product be stored near oxidising agents: No\n\nShould the product be stored near alkaline materials: No\n\nWhat happens to cyanoacrylate adhesive in high heat during storage: It thickens and cures inside the tube\n\nHow should the nozzle be maintained after use: Wipe clean immediately and replace cap firmly\n\nDoes storing the capped tube in a sealed plastic bag help: Yes, it extends shelf life\n\nShould the nozzle touch the surface during application: No\n\nCan cyanoacrylate accelerator sprays reduce cure time: Yes\n\nCan cyanoacrylate debonders dissolve cured adhesive: Yes\n\nWhat are debonders typically based on: Acetone\n\nIs a thin or thick glue film stronger: Thin film produces a stronger bond\n\nHow many years has Selleys been operating: Over 80 years\n\nIs this product intended for professional use only: No, suitable for tradespeople and DIYers\n\n---\n\n## Label Facts Summary\n\n> **Disclaimer:** All facts and statements below are general product information, not professional advice. Consult relevant experts for specific guidance.\n\n### Verified label facts\n\n- **Product name:** Selleys Auto Fix Supa Glue\n- **Manufacturer:** Selleys, a division of DuluxGroup Australia Pty Ltd\n- **Product reference number:** SELGHSEN000017\n- **SDS version:** 8.0\n- **SDS issue date:** 3 June 2022\n- **Product type:** Ethyl cyanoacrylate adhesive (cyanoacrylate / super glue family)\n- **Physical form:** Clear liquid\n- **Tube volume:** 3 ml\n- **Cured bond appearance:** Clear / essentially invisible\n- **Primary ingredient:** Ethyl cyanoacrylate (CAS 7085-85-0) — present at greater than 60% w/w\n- **Secondary ingredient:** Hydroquinone (CAS 123-31-9) — present at less than 0.2% w/w\n- **Hydroquinone function:** Polymerisation inhibitor (prevents premature curing during storage)\n- **Cure mechanism:** Polymerisation on contact with moisture (no heat or UV required)\n- **Initial handling strength:** 1–2 minutes (varies by substrate and conditions)\n- **Full cure time:** 24 hours\n- **Recommended application volume:** One drop per 1–2 square centimetres; apply to one surface only\n- **Recommended hold time after application:** 30–60 seconds\n- **Hazard classification:** Hazardous under Australian WHS regulations\n- **Dangerous Goods classification (road):** Not classified\n- **Dangerous Goods classification (rail):** Not classified\n- **Dangerous Goods classification (sea/IMDG):** Not classified\n- **Dangerous Goods classification (air/IATA):** Not classified\n- **Suitable substrates:** Metals, ceramics, porcelain, hard plastics (ABS, acrylic, polystyrene), rubber, glass\n- **Unsuitable substrates:** Polyethylene, polypropylene, PTFE (Teflon), highly porous materials (e.g. untreated wood, foam)\n- **Storage requirements:** Cool, dry location; away from direct sunlight, heat sources, oxidising agents, and alkaline materials\n- **Keep away from:** Children and pets\n- **Eye contact first aid:** Flush with running water for a minimum of 15 minutes; seek immediate medical attention; do not force open a bonded eyelid\n- **Skin contact first aid:** Soak in warm soapy water; gently peel or roll apart; do not force bonded skin; acetone may assist removal\n- **Inhalation first aid:** Move to fresh air; seek medical attention if symptoms persist\n- **Ingestion first aid:** Do not induce vomiting; seek immediate medical attention\n- **Vapour hazard:** Can irritate eyes, nose, and throat; use in well-ventilated areas only\n- **Nozzle maintenance:** Wipe clean immediately after use; replace cap firmly; store capped tube in sealed plastic bag to extend shelf life\n- **Accelerators:** Compatible with separate cyanoacrylate accelerator sprays\n- **Debonders:** Cured adhesive can be dissolved with acetone-based cyanoacrylate debonders\n\n---\n\n### General product claims\n\n- Delivers professional-grade bonding performance for tradespeople and DIYers\n- No complex preparation or specialised equipment required\n- Backed by Selleys' heritage of quality and innovation\n- Ethyl cyanoacrylate concentration described as delivering outstanding bonding performance\n- Suitable for reliable, load-bearing bonds, not temporary fixes\n- Compact 3 ml format reduces waste and keeps accidental spills manageable\n- Thin film application produces a stronger bond than thick application\n- Higher humidity accelerates cure; lower humidity and low-porosity surfaces may extend initial set time\n- Closer surface fit produces a stronger bond\n- Cool surfaces slow cure; warm surfaces and high humidity accelerate cure; room temperature recommended for most consistent results\n- Selleys has over 80 years of operating history\n- Suitable for both tradespeople and everyday DIYers, not professional use only\n- Avoiding nozzle-to-surface contact keeps the tube usable job after job\n- Acting before full cure is preferable to using a debonder for repositioning",
  "geography": {},
  "metadata": {},
  "publishedAt": "",
  "workspaceId": "77ac21fe-85f0-45c0-8279-2da0c52dc749",
  "_links": {
    "canonical": "https://directory.selleys.com.au/web-crawled-products/selleys-auto-fix-windscreen-sealant-black-100ml-07/"
  },
  "productInfo": {
    "stock": true
  },
  "productFeedItemId": "29102f2a-89e6-485b-b13e-dddcd3bcb025"
}